EDA TEC ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer

Hardver kézikönyv

Ez a fejezet bemutatja a terméketview, csomaglista, megjelenés, gomb, jelző és kezelőfelület.

Felettview
The ED-IPC2500 is a 5G industrial computer based on the Raspberry Pi CM4. Depending on the application scenario and user requirements, computer systems with different RAM and eMMC specifications can be selected.

• RAM options include 1GB, 2GB, 4GB, and 8GB.
• eMMC options include 8GB, 16GB, and 32GB.

The ED-IPC2500 provides commonly used interfaces such as HDMI, USB 2.0, and Ethernet. It supports network access via Wi-Fi, Ethernet, and 5G. The integration of a supercapacitor backup power supply (optional), RTC (Real-Time Clock), Watch Dog, EEPROM, and an encryption chip enhances the product’s ease of use and reliability. It is mainly used in industrial control and Internet of Things (IoT) fields.

Csomagolási lista

• 1 x ED-IPC2500 Unit
• [WiFi/BT Version – optional] 1 x 2.4GHz/5GHz Wi-Fi/BT Antenna

Megjelenés
Az egyes paneleken található interfészek funkcióinak és definícióinak bemutatása.

Előlap
Ez a szakasz az előlap funkcióit és definícióit mutatja be.

NEM.	Funkció meghatározása
1	1 x piros tápellátásjelző, amely a készülék be- és kikapcsolt állapotának ellenőrzésére szolgál.
2	1 x zöld 5G jelzőfény, amely a 5G jel állapotának ellenőrzésére szolgál.
3	1 x DC input, 2-Pin 3.5mm spacing phoenix terminals with screw holes. It supports 9V~36V input, the signal is defined as VIN+/GND.
4	3 × 1000M Ethernet interfaces (ETH0–ETH2), RJ45 connector with LED indicators, 10/100/1000M auto-sensing interfaces for Ethernet connection.
5	1 x zöld rendszerállapot-jelző, amely az eszköz működési állapotának ellenőrzésére szolgál.
6	1 x zöld felhasználói jelző, a felhasználó az aktuális alkalmazásnak megfelelően testreszabhatja az állapotot.

Hátsó panel
Ez a szakasz bemutatja a hátlap interfészeit és definícióit.

NEM.	Funkció meghatározása
1	1 x 5G antenna port, SMA csatlakozó, amelyhez 5G antenna csatlakoztatható.
2	1 x Micro SD card slot, functionally reserved only.
3	1 x Nano SIM card slot for installing a Nano SIM card to access 5G signals.
4	1 x Wi-Fi/BT antenna port (opcionális), SMA csatlakozó, amely Wi-Fi/BT antennához csatlakoztatható.
5	1 x Micro USB port, it supports to flash to eMMC for the system.
6	1 x 5G antenna port, SMA csatlakozó, amelyhez 5G antenna csatlakoztatható.

Oldalsó panel
Ez a szakasz bemutatja az oldalsó panel interfészeit és definícióit.

NEM.	Funkció meghatározása
1	1 x Reset gomb, rejtett gomb, nyomja meg a gombot az eszköz újraindításához.
2	2 x USB 2.0 ports, Type-A connector, each channel supports up to 480Mbps.
3	1 x 5G antenna port, SMA csatlakozó, amelyhez 5G antenna csatlakoztatható.
4	1 x HDMI port, Type-A connector, which is compatible with the HDMI 2.0 standard and supports 4K 60Hz. It supports connecting a displayer.
5	1 x 5G antenna port, SMA csatlakozó, amelyhez 5G antenna csatlakoztatható.

GombA 
ED-IPC2500 device includes a RESET button, which is a hidden button, and the silkscreen on the case is “RESET”. Pressing the RESET button will reset the device.

Indbicator
Introducing the various statuses and meanings of indicators contained in the ED-IPC2500 device.

Indikátor	Állapot	Leírás
PWR	On	A készüléket bekapcsolták.
	Pislogás	The power supply of the device is abnormal. Please stop the power supply immediately.
	Le	A készülék nincs bekapcsolva.
ACT	Pislogás	A rendszer sikeresen elindult, és adatokat olvas és ír.
	Le	The device is not powered on or does not read or write data.
FELHASZNÁLÓ	On	The user can customize a status according to the actual application.
	Le

Indikátor	Állapot	Leírás
		The device is not powered on or not defined by the user, and The default status is off.
5G	On	The dial-up is successful and the connection is normal.
	Le	5G signal is not connected or the device is not powered on.
Yellow indicator of the Ethernet port	On	The data transmission is abnormal.
	Pislogás	Az adatátvitel az Ethernet porton keresztül történik.
	Le	Az Ethernet kapcsolat nincs beállítva.
Az Ethernet port zöld jelzőfénye	On	Az Ethernet kapcsolat normál állapotban van.
	Pislogás	Az Ethernet-kapcsolat rendellenes.
	Le	Az Ethernet kapcsolat nincs beállítva.

Felület
Introducing the definition and function of each interface in ED-IPC2500 device.

SIM-kártya nyílás

The ED-IPC2500 device includes one Nano SIM card slot labeled with the silkscreen “ “, which is used for installing a SIM card to access 5G signals.

Power Interface
The ED-IPC2500 device features one power input terminal, implemented as a 2-Pin 3.5mm-pitch phoenix connector. The interface is labeled with the silkscreen “VIN+/GND”, and the pin definitions are as follows.

1000M Ethernet Interface (ETH0 ~ ETH2)

The ED-IPC2500 device includes three auto-sensing 10/100/1000M Ethernet interfaces, labeled with the silkscreen ““. These interfaces utilize RJ45 connectors, and for Ethernet connectivity, it is recommended to use Category 6 (Cat6) or higher-specification network cables. The pin definitions for the terminals are as follows:

HDMI interfész
The ED-IPC2500 device features one HDMI interface with a silkscreen label “HDMI”, designed as a standard Type-A connector. It supports connection to HDMI displays and delivers video output up to 4K resolution at 60Hz (4K@60).

USB 2.0 interfész
The ED-IPC2500 device features two USB 2.0 interfaces, labeled with the silkscreen ” “. These utilize standard Type-A connectors, supporting connectivity with standard USB 2.0 peripherals and providing data transfer speeds up to 480 Mbps.

Mikro USB interfész
The ED-IPC2500 device includes one Micro USB interface with a silkscreen label ” PROGRAMMING”. It supports flashing to eMMC when connected to a PC.

Wi-Fi Antenna Interface (optional)
The ED-IPC2500 device features one Wi-Fi antenna interface using an SMA connector, with a silkscreen label “WiFi/BT”, for connecting a dual-purpose Wi-Fi/Bluetooth antenna.

TIPP
If the selected device model is a non-Wi-Fi version, this interface will not be included.

5G antenna interfész
The ED-IPC2500 device features four 5G antenna interfaces using SMA connectors, with silkscreen labels “5G”, for connecting 5G antennas.

Supercapacitor (optional)
The ED-IPC2500 supports an optional supercapacitor backup power source, which provides the following functions:

• Power Failure Data Preservation: In the event of sudden power loss to the IPC device, the supercapacitor provides brief power support to critical circuitry within the IPC. Depending on the load, it can maintain operation for approximately one minute under lighter loads or about 30 seconds under heavier loads. This ensures that essential data (such as the device’s runtime state, current values of counters/timers, etc.) is preserved, preventing loss due to unexpected power interruption. This is critical for industrial applications requiring rapid process recovery without loss of key information.
• Real-Time Clock (RTC) Sustenance: The device’s RTC is crucial for recording event timestamps and sequencing operations. The supercapacitor supplies sufficient power to sustain the RTC circuit after primary power failure, allowing it to continue operating normally for a period.
• Assisting Graceful Shutdown: The supercapacitor supports an orderly shutdown procedure during power loss by supplying energy to the device’s control circuits. This enables the system to safely terminate active functions per predefined protocols—e.g., closing communication ports, halting complex calculations, or stopping runtime processes methodically.

TIPP
The supercapacitor requires at least five minutes of charging while the device is powered on. Full functionality is guaranteed only after the supercapacitor is fully charged.

Összetevők telepítése

This chapter describes the specific operational procedures for installing antennas and SIM card.

Antennák telepítése
The ED-IPC2500 device supports 5G and optional Wi-Fi functionality, with 5G requiring four antennas and Wi-Fi requiring one antenna. Antennas must be installed before operating the device.

Készítmény:
Ensure the corresponding antennas have been retrieved from the packaging box. When multiple antennas are included, they should be identified by the labels on each antenna.

Lépések:

1. Locate the antenna interfaces on the device side as indicated in the diagram alatt.TIPP
   The antenna interfaces are located on both the rear panel and side panel of the device. This demonstration will exclusively use the rear panel as an example magyarázatért.
2. Align the corresponding interfaces on both the device and antenna, then tighten clockwise to ensure a secure connection.

Nano SIM kártya beszerelése
The ED-IPC2500 device with 5G capability requires a SIM card to be installed first before utilizing the 5G functionality.

JEGYZET
Hot-swapping of the SIM card is NOT supported.

Készítmény:
The 5G Nano SIM card to be used has been obtained.

Lépések:

1. Locate the position of the Nano SIM card slot on the device side as indicated in the diagram below.
2. Insert the Nano SIM card with its golden contacts facing down into the corresponding slot. An audible click indicates successful installation.

Az eszköz indítása

Ez a fejezet bemutatja, hogyan kell kábeleket csatlakoztatni és elindítani az eszközt.

Csatlakozó kábelek
Ez a rész a kábelek csatlakoztatását írja le.

Készítmény:

• Verified operational peripherals have been obtained, including display, mouse, keyboard, and power adapter.
• A functional network connection has been established.
• Operational HDMI and Ethernet cables have been secured.

A csatlakozó kábelek sematikus rajza:
For specific pin definitions of each interface and wiring methods, refer to 1.6 Interface.

A rendszer első indítása
The ED-IPC2500 device does not feature a power switch. Upon connecting to a power source, the system will initiate startup.

• Solid red PWR LED: Indicates normal power supply to the device.
• Blinking green ACT LED: Signals successful system initialization, followed by the Raspberry Pi logo appearing in the top-left corner of the display.

TIPP

• Default username: pi
• Default password: raspberry

Raspberry Pi operációs rendszer (asztali)
If the Desktop edition of the system is preinstalled at the factory, the device will boot directly into the desktop environment upon completion of startup, as shown in the figure below.

Raspberry Pi OS (Lite)
If the Lite edition of the system is preinstalled at the factory, the device will automatically log in using the default username pi (password: raspberry ) upon startup completion. The interface shown below signifies a successful system boot.

Rendszer konfigurálása

Ez a fejezet bemutatja, hogyan konfigurálhatja a rendszert.

1. Eszköz IP-címének megkeresése
   Eszköz IP-címének megkeresése
2. Távoli bejelentkezés
   Távoli bejelentkezés
3. Tárolóeszközök konfigurálása
   Tárolóeszközök konfigurálása
4. Ethernet IP-cím konfigurálása
   Ethernet IP-cím konfigurálása
5. Configuring Wi-Fi (Optional)
   A Wi-Fi konfigurálása
6. Configuring Bluetooth (Optional)
   Bluetooth konfigurálása
7. 5G konfigurálása
   The ED-IPC2500 natively supports 5G functionality, but specific configurations must be performed before utilizing the 5G network.
   1. Scenarios Requiring No APN Configuration
      If the user’s 5G network operates without APN configuration, connect by proceeding as follows:
      Készítmény:The ED-IPC2500 device has completed normal startup.
      • A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.

JEGYZET : Hot-swapping of the SIM card is NOT supported.

Lépések:

1. Open a terminal window and execute the following command to launch the 5G monitoring utility and automatically connect to the 5G hálózat.TIPP
   After executing the command, the terminal window will display relevant log information.
2. Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).The returned information is shown in the following figure:
   • If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
   • If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.

Scenarios Requiring APN Configuration
If the user’s 5G network requires APN configuration, configure the settings by proceeding as follows:

Készítmény:

• The ED-IPC2500 device has completed normal startup.
• A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.
• APN credentials have been acquired, including the APN name, username, and password. The following example information will be used for demonstration:
  • APN név: APN1
  • Felhasználónév: admin
  • Jelszó: admin

JEGYZET
Hot-swapping of the SIM card is NOT supported.

Lépések:

Open a terminal window and sequentially execute the following commands to access the ed-qml—conf configuration file.

Configure the “APN Config” settings as required by setting the “apn”, “apn_user”, and “apn_password” parameters.

TIPP
The “ping_server” and “online_script” parameters under the “Network” section also support user-specific configuration as required.

Enter Ctrl+O to save the file, then press Enter to confirm, and finally, input Ctrl+X to exit file editing mode.
Execute the following command to launch the 5G monitoring utility and automatically establish the 5G network.

TIPP
After executing the command, the terminal window will display relevant log information.

Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).

The returned information is shown in the following figure:

• If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
• If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.

Essential Configuration Commands

Parancs	Leírás
sudo systemctl start ed-lte-daemon.service	Establishing the 5G Network Connection via Service
sudo systemctl enable ed-lte-daemon.service	Automatically start the service during boot
sudo ed-lte-tool -r	Resetting the 5G Module
sudo ed-lte-tool -m	Viewing 5G Module Information
sudo ed-lte-tool -s	Viewing 5G Signal Strength
sudo ed-lte -c	Dial-up networking does not support automatic reconnection after disconnection.
sudo ed-lte -d	Disconnect the network connection
cd /var/log/ed-qmi/ sudo nano xxxx-xx-xx.log	Navigate to the `/var/log/ed-qmi/` directory and review a rönk files, where `xxxx-xx-xx` denotes the date in Year-Month-Day format (e.g., 2025-06-18).
journalctl -u ed-lte-daemon.service	Monitor real-time logs for the 5G network

Hangjelző konfigurálása
RTC konfigurálása
A USER indikátor konfigurálása

ÉRINTKEZÉS

Email: sales@edatec.cn / support@edatec.cn
Web: www.edatec.cn
Telefon: +86-15921483028(China) | +86-18217351262(Overseas)

Dokumentumok / Források

EDA TEC ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer [pdf] Felhasználói kézikönyv ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer, ED-IPC2500, 5G Raspberry Pi CM4 Industrial Computer, Pi CM4 Industrial Computer, Industrial Computer

Hivatkozások

• Felhasználói kézikönyv